Allen-Bradley 1756-CNB/E Скачать руководство пользователя страница 152

Страница: 152 / 186

Publication 1756-UM523F-EN-P - December 2006

152

Set Up EtherNet/IP Communication Across Subnets

Create an Alias Topic

1. In RSLinx software, choose DDE/OPC

⇒

Alias Topic Configuration.

2. Type a name for the alias topic that will communicate with this pair of redundant controllers.

3. Add the topic for each redundant controller to

the Aliased Topics list.

To add a topic, select the topic and choose

4. Check the Switch on command check box.

Uncheck the remaining check boxes.

This lets the ControlLogix Redundancy Alias
Topic Switcher software control which topic the
alias topic uses for communication.

5. Click

and then

Содержание 1756-CNB/E



























































































































































































Результаты поиска

Содержание 1756-CNB/E

Отзывы:

Похожие инструкции для 1756-CNB/E

Бренды по названию

Популярные бренды

Allen-Bradley 1756-CNB/E, Руководство пользователя

Результаты поиска

Содержание 1756-CNB/E

Отзывы:

Похожие инструкции для 1756-CNB/E

Бренды по названию

Популярные бренды