Allen-Bradley 1756-CNB/E Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 186

background image

Publication 1756-UM523F-EN-P - December 2006

38

Design the System

Planning an EtherNet/IP
Network

Follow these guidelines as you plan your EtherNet/IP network.

EtherNet/IP Network Guidelines

Guideline

Details

Use EtherNet/IP

only

for HMIs, workstations, and

messaging.

In a redundant system, use an EtherNet/IP network only for HMI, workstation,
and message communication. Do not use an EtherNet/IP network for:

•

control of I/O modules.

•

peer interlocking (produced and consumed tags).

Important

: RSLogix 5000 software lets you set up and download a project

that tries to use an EtherNet/IP network for I/O, produced tags, or consumed
tags. Those communications do not work however.

Are communication delays OK during a switchover?

If Yes, then continue with EtherNet/IP.

If No, then use ControlNet.

Communication stops over an EtherNet/IP network with your controllers and
HMIs during a switchover.

•

You will not be able to communicate with them for up to a minute.

•

The actual delay depends on your network topology.

If you need bumpless communication, use a ControlNet network.

If you need a redundant network, use ControlNet.

2 EtherNet/IP modules in same chassis does not give you redundant
EtherNet/IP communication. A switchover still happens if one of the modules
fails or a cable breaks.

See How an EtherNet/IP Module Handles a Cable Break on page 40.

Make sure that your ENBT modules are catalog revision
E01 or later.

To use a 1756-ENBT module in a redundant controller chassis, make sure the
catalog revision of the module is greater than or equal to E01 (E01, E02, …,
F01).

•

To find the catalog revision, look at the label on the side of the module or
box.

•

If you use an older ENBT module, your secondary chassis will not
synchronize.

Control

Log

1756-ENBT

CAT. NO./SERIES

E01

CAT. REV.

Ethernet/IP 10/100

Catalog Revision

«
...
36
37
38
39
40
...
»

Содержание 1756-CNB/E



























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1756-CNB/E

Бренд: C.Nord Страницы: 100

CoreBuilder 9000

Бренд: 3Com Страницы: 78

REMOTE ACCESS SYSTEM 1500

Бренд: 3Com Страницы: 62

Бренд: Ebyte Страницы: 35

Бренд: Gascat Страницы: 32

Бренд: Garz & Fricke Страницы: 35

Бренд: Harman Kardon Страницы: 25

Бренд: Uniss Страницы: 21

Бренд: Oceanic Страницы: 11

Бренд: Radware Страницы: 98

Бренд: RabbitCore Страницы: 34

Бренд: ValvTechnologies Страницы: 20

NOVASTAT EL DIGITAL

Бренд: Taconova Страницы: 7

Бренд: Technische Alternative Страницы: 68

PDS CONTROL Series

Бренд: S&P Страницы: 32

Бренд: Danfoss Страницы: 2

Бренд: XtendLan Страницы: 12

Бренд: ZBA Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды