Allen-Bradley 1756-CNB/E Скачать руководство пользователя страница 107 | Manualshive

Страница: 107 / 186

background image

Publication 1756-UM523F-EN-P - December 2006

Maintain and Troubleshoot the System

107

Update a Keeper Signature

To see if the keeper signature of a CNB module is stopping the
secondary chassis from synchronizing, you need to update the keeper
signature.

To update the keeper signature, perform this procedure when a
secondary chassis will not synchronize and its CNB modules show !CPT.

Before You Begin

The secondary chassis will not synchronize if the keeper signature of
a CNB module does not match its partner. This happens if you
schedule the ControlNet network while the secondary chassis is off or
if the CNB module was previously configured in a different network.

Actions

1.

Start RSNetWorx for ControlNet software. Has this network been
scheduled before?

2.

From the Network menu, choose Keeper Status.

3.

Make sure the list contains all your keeper capable nodes. This
includes the CNB modules in the secondary chassis.

If

Then

No

A. From the File menu, select New.

B. From the Network menu, select Online.

C. Select your ControlNet network and choose OK.

Yes

A. From the File menu, select Open.

B. Select the file for the network and choose Open.

C. From the Network menu, select Online.

3.

4.

Keeper Capable Node

Active Keeper

Valid Keeper

Offline file

01

No

No

02

Yes

Yes

Secondary Chassis

42797

! C p t

«
...
105
106
107
108
109
...
»

Содержание 1756-CNB/E



























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1756-CNB/E

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 40

Бренд: B&G Страницы: 2

Бренд: B&K Страницы: 9

Бренд: UNITED Страницы: 22

Бренд: Samson Страницы: 56

Бренд: Hach Страницы: 128

Бренд: Yamato Страницы: 33

Бренд: Jabra Страницы: 3

Бренд: Jedia Страницы: 12

Бренд: JED Micro Страницы: 10

Бренд: JCM Technologies Страницы: 2

Бренд: Oceanic Страницы: 11

Бренд: Penn Страницы: 10

Бренд: Rain Bird Страницы: 11

Бренд: Equalizer Страницы: 26

LOOPDRIVE FIM-RC

Бренд: 4EVAC Страницы: 2

Бренд: Gain Electronic Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды