Allen-Bradley 1756-CNB/E Скачать руководство пользователя страница 137

Страница: 137 / 186

Publication 1756-UM523F-EN-P - December 2006

Update Modules and Redundant Systems

137

3. Disqualify the secondary chassis,

A. Click Configuration.

B. Set Auto-Synchronization to Never.

C. Choose Apply and then Yes to confirm.

D. Click Synchronization.

E. Choose Disqualify Secondary and then Yes to confirm.

4. Upgrade the required firmware of the

secondary chassis.

See the ControlLogix Controller and Memory Board Installation Instructions, publication
1756-IN101.

5. Make the secondary controller the new

primary controller.

A. Start RSLogix 5000 software.

B. Download the project to the secondary controller.

C. When it is safe to stop the system, change the primary controller to Program Mode.

D. Turn off power to the primary chassis.

E. Go to the 1757-SRM properties of the secondary chassis.

F. Choose Become Primary.

6. Clear the fault of the new primary

controller.

A. In RSLogix 5000 software, go online to the new primary controller.

B. The controller is faulted. When a disqualified secondary controller becomes a primary

controller, the controller experiences a major fault.

C. From the Communications menu, choose Clear Faults.

D. To start control of the process, from the Communications menu, choose Run Mode.

7. Upgrade the other redundant chassis.

A. Turn on power to the other redundant chassis.

B. Upgrade the required firmware of the chassis.

8. Change the Auto-Synchronization Option

to Always.

A. Open the SRM configuration tool for the primary chassis.

B. On the Configuration tab, change the Auto-Synchronization option to Always.

C. Choose OK.

Action

Details

Содержание 1756-CNB/E



























































































































































































Результаты поиска

Содержание 1756-CNB/E

Отзывы:

Похожие инструкции для 1756-CNB/E

Бренды по названию

Популярные бренды

Allen-Bradley 1756-CNB/E, Руководство пользователя

Результаты поиска

Содержание 1756-CNB/E

Отзывы:

Похожие инструкции для 1756-CNB/E

Бренды по названию

Популярные бренды