Allen-Bradley 1756-CNB/E Скачать руководство пользователя страница 32

Страница: 32 / 186

Publication 1756-UM523F-EN-P - December 2006

Design the System

Placement of Operator
Interface Terminals

For operator interface terminals, stay within these limitations.

Operator Interface Terminal Limitations

Network

Operator Interfaces

Guidelines

EtherNet/IP network

PanelView Standard terminal

Same as a nonredundant system

•

PanelView Plus terminal

•

VersaView industrial computer running a
Windows CE operating system

•

Use RSLinx Enterprise software revision 3.0 or
later.

•

Set aside connections for each PanelView Plus or
VersaView CE terminal.

RSView Supervisory Edition software with RSLinx
Enterprise software

•

Use RSLinx Enterprise software revision 3.0 or
later.

•

Use IP swapping.

•

Keep the HMI and both redundant chassis on the
same subnet.

•

RSView Supervisory Edition software with
RSLinx 2.

software

•

RSView 32 software

•

Any other HMI client software that uses
RSLinx 2.

software

Limit the number of RSLinx servers that a controller
uses to 1 (ideal) to 3 (maximum).

ControlNet network

•

PanelView Standard terminal

•

PanelView 1000e/1400e terminal

Do your terminals use unscheduled communication?

•

Yes — Use

≤

4 terminals per controller.

•

No — Use the number of terminals that you need.

•

PanelView Plus terminal

•

VersaView industrial computer running a
Windows CE operating system

Set aside connections for each PanelView Plus or
VersaView CE terminal.

•

RSView Supervisory Edition software

•

RSView 32 software

•

Any other HMI client software that uses
RSLinx 2.

software

Limit the number of RSLinx servers that a controller
uses to 1 (ideal) to 3 (maximum).

In this module

Set aside

Controller

5 connections

CNB

5 connections

ENBT

5 connections

EWEB

5 connections

In this module

Set aside

Controller

5 connections

CNB

5 connections

Содержание 1756-CNB/E



























































































































































































Результаты поиска

Содержание 1756-CNB/E

Отзывы:

Похожие инструкции для 1756-CNB/E

Бренды по названию

Популярные бренды

Allen-Bradley 1756-CNB/E, Руководство пользователя

Результаты поиска

Содержание 1756-CNB/E

Отзывы:

Похожие инструкции для 1756-CNB/E

Бренды по названию

Популярные бренды