Allen-Bradley 1756-CNB/E Скачать руководство пользователя страница 136

Страница: 136 / 186

Publication 1756-UM523F-EN-P - December 2006

136

Update Modules and Redundant Systems

Update a Redundant
Control System Offline

Complete this procedure to upgrade the revision of your redundant
modules. This procedure minimizes the time your process is down
during an upgrade.

IMPORTANT

Do not connect your computer to the network access port on a
CNB module in the primary chassis. You will lose access to the
network when you turn off power to the chassis.

Action

Details

1. Upload and save the project.

Do you have an up-to-date copy of the project for the controller stored offline?

•

Yes — Go to step 2.

•

No — Continue with step A.

A. Upload the project in the primary controller.

B. Save the project.

2. Open the SRM configuration tool for the

secondary chassis.

A. Start RSLinx software.

B. From the Communications menu, choose RSWho.

C. Open the branches of your network until you find the 1757-SRM module in the primary

chassis.

D. Right-click the SRM and choose Module Configuration.

Содержание 1756-CNB/E



























































































































































































Результаты поиска

Содержание 1756-CNB/E

Отзывы:

Похожие инструкции для 1756-CNB/E

Бренды по названию

Популярные бренды

Allen-Bradley 1756-CNB/E, Руководство пользователя

Результаты поиска

Содержание 1756-CNB/E

Отзывы:

Похожие инструкции для 1756-CNB/E

Бренды по названию

Популярные бренды