Allen-Bradley 1756-CNB/E Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 186

background image

Publication 1756-UM523F-EN-P - December 2006

Configure the System Redundancy Module

55

What to Do Next

Check the Revision of Your
SRM Configuration Tool

Check the revision of your SRM configuration tool to make sure that
you are using the right revision of the SRM configuration tool for your
ControlLogix redundancy system.

Perform this procedure to:

•

use the SRM configuration tool for the first time.

•

connect to a different ControlLogix redundancy system for the
first time.

•

update the firmware of a ControlLogix redundancy system.

Before You Begin

RSLinx software automatically installs the SRM configuration tool. Use
this table to see which revision of the tool that you get.

RSLinx Software Versions

IMPORTANT

Make sure that you check the revision of your SRM
configuration tool before you use it. Later revisions of the SRM
configuration tool are not compatible with earlier revisions of
ControlLogix redundancy systems. See Check the Revision of
Your SRM Configuration Tool on page 55.

IMPORTANT

Make sure that you check the revision of your SRM
configuration tool.

•

Revision 2.6 is compatible only with revision 13.

x

or later

ControlLogix redundancy systems.

•

You will cause the 1757-SRM module to fault if you use
revision 2.6 of the tool with an revision 11.

x

or earlier

redundancy systems.

Software

Installed Tool

RSLinx software, version 2.42

SRM configuration tool revision 2.5

RSLinx software, version 2.43

SRM configuration tool revision 2.6

RSLinx software, version 2.52

SRM configuration tool revision 3.6

«
...
53
54
55
56
57
...
»

Содержание 1756-CNB/E



























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1756-CNB/E

Бренд: J4C Страницы: 4

Бренд: ABB Страницы: 6

Бренд: KAR-TECH Страницы: 28

Бренд: 2iB Страницы: 5

Go!Control Panel

Бренд: 2gig Technologies Страницы: 78

Бренд: Watts Страницы: 2

Бренд: Hanbay Страницы: 18

VLT AQUA Drive FC 202

Бренд: Danfoss Страницы: 124

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 8

Бренд: Danfoss Страницы: 114

Бренд: Danfoss Страницы: 16

Бренд: Danfoss Страницы: 24

Бренд: Danfoss Страницы: 8

ECL Comfort 296

Бренд: Danfoss Страницы: 159

VLT AutomationDrive FC 301

Бренд: Danfoss Страницы: 78

Бренд: Danfoss Страницы: 20

ECL Comfort 210

Бренд: Danfoss Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды