Allen-Bradley 1756-CNB/E Скачать руководство пользователя страница 131

Страница: 131 / 186

Publication 1756-UM523F-EN-P - December 2006

Update Modules and Redundant Systems

131

3. Open the SRM configuration tool for the

primary chassis.

A. Start RSLinx software.

B. From the Communications menu, choose RSWho.

C. Open the branches of your network until you find the 1757-SRM module in the primary

chassis.

D. Right-click the 1757-SRM module and choose Module Configuration.

4. Disqualify the secondary chassis,

A. Click Configuration.

B. Set Auto-Synchronization to Never.

C. Choose Apply and then Yes.

D. Click Synchronization.

F. Click OK.

Action

Details

E. Click Disqualify Secondary and then Yes.

The secondary chassis

is disqualified.

Содержание 1756-CNB/E



























































































































































































Результаты поиска

Содержание 1756-CNB/E

Отзывы:

Похожие инструкции для 1756-CNB/E

Бренды по названию

Популярные бренды

Allen-Bradley 1756-CNB/E, Руководство пользователя

Результаты поиска

Содержание 1756-CNB/E

Отзывы:

Похожие инструкции для 1756-CNB/E

Бренды по названию

Популярные бренды