Allen-Bradley 1756-CNB/E Скачать руководство пользователя страница 134

Страница: 134 / 186

Publication 1756-UM523F-EN-P - December 2006

134

Update Modules and Redundant Systems

8. Reset the secondary CNB modules.

A. Cycle power to the secondary chassis.

B. On the Synchronization Status tab of the configuration tool, verify that the modules

show full compatibility.

9. Synchronize the secondary chassis.

A. Click Synchronization.

B. Click Synchronize Secondary and then Yes.

C. Wait for the chassis to synchronize.

10. Initiate a switchover.

Click Initiate Switchover and Yes.

11. Replace the CNB modules in the new

secondary chassis.

Repeat steps 6-8 for the CNB modules in the new secondary chassis.

Action

Details

The chassis are synchronized.

Содержание 1756-CNB/E



























































































































































































Результаты поиска

Содержание 1756-CNB/E

Отзывы:

Похожие инструкции для 1756-CNB/E

Бренды по названию

Популярные бренды

Allen-Bradley 1756-CNB/E, Руководство пользователя

Результаты поиска

Содержание 1756-CNB/E

Отзывы:

Похожие инструкции для 1756-CNB/E

Бренды по названию

Популярные бренды