ALDI WZTS 2000 Скачать руководство пользователя страница 30

Страница: 30 / 41

Operation

www.einhell.co.uk

AFTER SALES SUPPORT

GB IRE

IRE

0044 151 649 1500

0044 1890 946 244

5. Rotate the saw blade all the way out of the saw table by turning the crank

clockwise up to the stop point.

6. Remove the splitting wedge by loosening the clamp bolt

by turning it

clockwise a few revolutions and then pulling the splitting wedge up and out.

7. Use the saw blade key

to fix the saw blade:

The retaining lugs on the saw blade key extend

into the openings in the middle of the saw

blade.

8. Use the ring spanner

to turn the hexagon

bolt

counterclockwise to loosen it.

9. Carefully hold the saw blade with one hand

and remove the hexagon bolt, the pressure

disc

and the outer saw blade flange

from the drive shaft.

23 44 42 41

10. Now take the saw blade off of the drive shaft and carefully pull it up and out of the

saw table.

11. Clean the outer and inner saw blade flange thoroughly before mounting a new

saw blade.

12. Mount a new saw blade on the drive shaft. In the process, observe the direction of

rotation: the cutting edge of the blade teeth must point in the direction of rotation

(to the front). Usually, the direction of rotation is indicated on the saw blade.

13. Place the outer saw blade flange back on the drive shaft. At the same time, make

sure that the outer saw blade flange is correctly aligned.

14. Run the hexagon bolt through the pressure disc and into the drive shaft and

secure it tightly with your hand.

15. Carefully turn the saw blade in the direction of rotation: It must be exactly centred

and must not “wobble”. Check to make sure that the saw blade, outer flange and

pressure disc are correctly positioned if the saw blade is not properly centred and

realign the parts.

16. Use the saw blade key to hold the saw blade in place and use the ring spanner to

turn the hexagon bolt tight.

17. Mount the splitting wedge, the table insert and the saw blade guard as described

in the chapter “Mounting/adjusting the splitting wedge”.

Содержание WZTS 2000










































Результаты поиска

Содержание WZTS 2000

Отзывы:

Бренды по названию

Популярные бренды

ALDI WZTS 2000, Руководство пользователя

Результаты поиска

Содержание WZTS 2000

Отзывы:

Бренды по названию

Популярные бренды