manualshive.com logo in svg

ALDI WZTS 2000, Руководство пользователя

Поделиться
Скачать
ALDI WZTS 2000 Скачать руководство пользователя страница 28

Operation

28

www.einhell.co.uk

AFTER SALES SUPPORT

28

GB IRE

GB

IRE

0044 151 649 1500

0044 1890 946 244

Performing bevel cuts

1. Set the saw blade

  44

 to the desired angle (see chapter “Setting the cutting 

angle”).

2. Set the parallel guide

  33

 corresponding to the width and height of the work 

piece (see section “Parallel guide”).

3. Perform the cut corresponding to the width of the work piece (see chapter 

“Performing lengthwise cuts”).

Performing cross cuts

 

WARNING!

Risk of injury!

Improperly handling the table saw poses a risk of serious injury.

 

− Always take hold of the guided work piece and never of the unguided 

work piece that is being cut off.

 

− Always push the cross guide forward until the work piece has been cut 

through completely.

1. Set the cross guide

  36

 as necessary (see chapter “Cross guide”).  

If the saw blade

  44

 is also to be set at an angle, push the cross guide into the 

right guide groove

  3

 to prevents your hand and the cross guide from coming 

into contact with the saw blade guard

  26

.

2. Lower the saw blade guard onto the saw table 

1

.  

The saw blade guard is pushed up by the work piece while sawing.

3. Firmly push the work piece against the cross guide.

4. Switch on the dust extractor first and then the table saw.
5. Push the cross guide and the work piece towards the saw blade to perform the 

cut.

6. Switch the table saw and the dust extractor off.

7. Let the cutting waste rest on the saw table until the saw blade returns to the 

resting position.

Cutting particleboards

To prevent raw edges when cutting particleboards, do not set the saw blade 

44

 

higher than 5 mm above the work piece thickness.

Содержание WZTS 2000










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды