manualshive.com logo in svg

ALDI WZTS 2000, Руководство пользователя

Поделиться
Скачать
ALDI WZTS 2000 Скачать руководство пользователя страница 27

Operation

27

www.einhell.co.uk

AFTER SALES SUPPORT

GB

IRE

0044 151 649 1500

0044 1890 946 244

GB IRE

Sawing

 

WARNING!

Risk of injury!

Improperly handling the table saw poses a risk of serious injury.

 

− When performing lengthwise cuts, do not stand directly in front of the 

table saw, instead stand diagonal to the cutting line.

 

− When performing bevel cuts, always use the parallel guide.

 

− Use a push stick or a push block to safely push the work piece through the 

saw blade. Immediately replace a damaged or worn push stick.

 

− Secure long work pieces so that they do not tip over at the end of the cut! 

Use e.g. a roller stand for this.

 

− Each time after making a new setting, perform a test cut to check 

the set dimensions.

 

− After switching on the table saw, wait until the saw blade has 

reached its maximum speed before you perform the cut.

 

− Attention when cutting into the workpiece!

 

− Only operate the table saw with an extraction device.

 

− Check and clean the suction channels regularly.

Performing lengthwise cuts

A lengthwise cut is applied to cut a work piece lengthwise. Push an edge of the work 

piece against the parallel guide

  33

 with the flat side on the saw table

  1

.

1. Adjust the parallel guide to the work piece height and the desired width (see 

chapter “Parallel guide”).

2. Lower the saw blade guard

  26

 onto the saw table.  

The saw blade guard is pushed up by the work piece while sawing.

3. Switch on the dust extractor first and then the table saw.

4. With your fingers closed, place your hands flat on the work piece and push it along 

the parallel guide into the saw blade

  44

.

5. Only guide it laterally to the front edge of the saw blade guard with your left or 

right hand (depending on the position of the parallel guide).

6. Always push the work piece up to the end of the splitting wedge

  29

.

7. Switch the table saw and the dust extractor off.

8. Let the cutting waste rest on the saw table until the saw blade returns to the 

resting position.

Содержание WZTS 2000










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды