manualshive.com logo in svg

ALDI WZTS 2000, Руководство пользователя

Поделиться
Скачать
ALDI WZTS 2000 Скачать руководство пользователя страница 15

Safety

15

www.einhell.co.uk

AFTER SALES SUPPORT

GB

IRE

0044 151 649 1500

0044 1890 946 244

GB IRE

 

− Observe the maximum speed. The maximum speed specified on the fitted 

tool must not be exceeded. Comply with the speed if specified.

 

− Do not use any fitted tools that are cracked. Dispose of any cracked fitted 

tools. It is not permissible to repair them.

 

− Clean any dirt, oil, grease and water off of the clamping surfaces.

 

− It is not permitted to use loose reducing rings or bushings to reduce bore 

holes in circular saw blades.

 

− Make sure that fixed reducing rings for securing the fitted tool have the 

same diameter and are at least 1/3 of the cutting diameter.

 

− Make sure that fixed reducing rings are parallel to one another.

 

− Handle the fitted tools carefully. Ideally, you should store them in the 

original packaging or special containers.  

Wear protective gloves for better grip and to further reduce the risk of 

injury.

 

− Before using fitted tools, make sure that all protective devices are properly 

secured.

 

− Before use, make sure that the fitted tool complies with the technical 

requirements of this power tool and that it is properly secured.

 

− Only use the enclosed saw blade for cutting wood and never use it to cut 

metals.

Supplementary safety instructions for the laser

• 

Do not point the laser beam at reflective surfaces or directly at 

persons or animals and do not look into the laser beam

. This laser 

emits a laser beam that falls under laser class 2 in accordance with EN 

60825-1:2014. You could blind people with it.

• 

A laser is not a toy and does not belong in the hands of children

. 

Using it incorrectly may result in irreparable damage to the eyes.

• 

It is forbidden to manipulate the laser so as to increase its power 

in any way

. No liability will be assumed for any damages caused as the 

result of failure to comply with these safety instructions.

• 

The laser does not contain any serviceable parts

. Therefore, do not 

open the housing. Otherwise, you will render the warranty void.

• 

Warning! Do not swap the laser with another type of laser. Only 

the manufacturer of the laser or an authorised representative may 

perform repairs

.

• 

Never switch the laser on or off while the table saw is running.

Содержание WZTS 2000










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды