Agilent Technologies Agilent 4396B, Руководство по обслуживанию

Страница: 240 / 324

The oscillator contains an 85.68 MHz V CO , a phase detector , a 1/2 divider , a mixer , and a 1/71
divider . See Figure 11-6. The V CO frequency (F
vco
) is divided by 2 and mixed with the 40 MHz
reference frequency in the mixer . The mixer then produces a shifted frequency (F
vco
/2 0 40
MHz). The mixer output is divided by 71 and then compared with the 40 kHz reference signal
in the phase detector . Phase locking imposes the condition of 40 kHz = (F
vco
/2 0 40 MHz)/71.
Therefore , the output frequency (F
vco
) is locked to 85.68 MHz (= (40 kHz x 71 + 40 MHz) x 2).
ALC
The ALC controls the level of the 21.42 MHz CW signal from the source OSC. The signal is
routed to the RF OUT connector through the A3A2 2nd LO , the A3A3 source , and the A7
Output Attenuator . The A3A3 output level is detected and loops back to the ALC for automatic
leveling control.
The ALC consists of a level D A C, an error detector , an integrator , a Gain ALC, and a level
vernier . See Figure 11-6. In addition, a switch that follows the level vernier is used to turn the
RF OUT signal on and o.
The loop-backed A3A3 output level is compared with the level D A C output in the error
detector . The error detector produces a DC voltage proportional to the error between the A3A3
output level and the level D A C output. The error detector output controls the 21.42 MHz signal
level through the integrator and the level vernier . ALC loop locking imposes the condition of
Level D A C Output = A3A3 Output Level. Therefore , the A3A3 output level is determined by
the level D A C setting.
The A3A3 output level for each level D A C setting is predened by performing the RF OUT
Level Correction Constants. The predened data is stored in the EEPROM of the A1 CPU .
The Gain ALC is a variable amplier from 0 dB to 6 dB . It is used to shorten the time required
for the ALC loop to be locked after the frequency is changed. It does this by compensating the
frequency response of the source amplier's gain in the A3A3 source . Therefore , the Gain ALC
setting depends on the RF signal frequency . The Gain ALC settings are predened over the
entire frequency range by performing the RF OUT Level Correction Constants. The predened
setting data is stored in the EEPROM of the A1 CPU .
A3A2 2nd LO
The A3A2 2nd LO generates the second local oscillator signal (a 2.08 GHz CW signal) and
converts the 21.42 MHz signal from the A3A1 ALC to a 2.05858 GHz IF signal by mixing the
21.42 MHz and the second local oscillator signal.
The 2.05858 GHz IF signal is supplied to the A3A3 source and then converter to a swept RF
signal. The second local oscillator signal is supplied to the A4A2 receiver RF .
The A3A1 ALC consists of the following circuits:
2nd LO
Source First Mixer
2nd Local OSC Circuit
The 2nd Local oscillator circuit is a phase locked oscillator . The output signal is phase locked
to the 520 MHz frequency from the A5 synthesizer . The oscillator generates a 2.08 GHz signal.
The signal is supplied to the source rst mixer and the A4A1 receiver RF .
The oscillator contains a 1.04 GHz V CO , a phase detector , and a 1/2 divider . See Figure 11-6 .
The V CO frequency (F
vco
) is divided by 2 and then compared with the 520 MHz reference signal
in the phase detector . Phase locking imposes the condition of 520 MHz = F
vco
/2. Therefore , the
output frequency (F
vco
) is locked to 1.04 GHz (= 520 MHz x 2). Then the signal frequency is
converted to 2.08 GHz by the doubler .
11-20 Theory of Operation