Agilent Technologies 34945A Скачать руководство пользователя страница 53

Страница: 53 / 124

Software Installation and Configuration

Agilent 34945A Microwave Switch/Attenuator Driver Module User’s Guide

work servers that support Dynamic Domain Name Service (DNS). For network

servers that do not support Dynamic DNS, only the IP address is reported.

Instrument Addressing

During programming, the 34980A/34945A is accessed

through its address string which consists of an IP address:

TCPIP0::169.254.86.15::inst0::INSTR

or host name:

TCPIP0::A-34980A-12345.agilent.com::inst0::INSTR

LAN Default Configuration

If necessary, the 34980A LAN interface can be reset to its default
configuration settings from the front panel. These settings are listed in Table
3-3.

Table 3-3. Default LAN Configuration Settings.

LAN Parameter

Default (Reset) Setting

DHCP

Automatic IP Addressing

IP Settings if DHCP Server
Unavailable

IP Address: 169.254.9.80 (default)
Subnet Mask: 255.255.0.0
Default Gateway: 0.0.0.0

DNS Server

0.0.0.0 (may be assigned by the DHCP server)

Host Name (registered with
DDNS if available)

A-34980A-last 5 digits of serial number

Net BIOS

LAN Keep Alive

1800 (seconds)

Ethernet Connection Monitoring

ON - instrument monitors its LAN connection;
will attempt to automatically reconnect if dis-
connected from network.

Password

None (disabled)

Содержание 34945A





























































































































Результаты поиска

Содержание 34945A

Отзывы:

Похожие инструкции для 34945A

Бренды по названию

Популярные бренды

Agilent Technologies 34945A, Руководство пользователя

Результаты поиска

Содержание 34945A

Отзывы:

Похожие инструкции для 34945A

Бренды по названию

Популярные бренды