Agilent Technologies 34945A Скачать руководство пользователя страница 47

Страница: 47 / 124

Software Installation and Configuration

Agilent 34945A Microwave Switch/Attenuator Driver Module User’s Guide

Installing the Agilent IO Libraries

The Agilent IO Libraries include the VISA and VISA-COM libraries used for

programming the 34945A in Microsoft



development environments (Table

3-1). The VISA and VISA-COM libraries allow you to send commands from the

34945A SCPI command set to the instrument (see “34945A Programmers Ref-

erence Help” on the Product Reference CD-ROM). The IO libraries also include

the ‘Configuration Expert’ utility described later in this chapter.

The IO Libraries are contained on the Agilent Automation-Ready CD or may be down-

oaded from the Agilent Developer Network website at:

http://adn.tm.agilent.com

Before installing the IO libraries, review Table 3-2 to verify that your computer

meets the specifications required for the software.

Table 3-2. Agilent IO Libraries Suite System Requirements.

Close all applications on your computer. Insert the Agilent Automation-Ready

CD into the CD-ROM drive. Follow the instructions as prompted for a

typical

installation.

Accept all default directories specified

N O T E

The Agilent IO Libraries must be installed prior to installing drivers (e.g. IVI-C,
IVI-COM) from the 34980A Product Reference CD or from any other source.

Processor

450 MHz Intel Pentium® II or higher

Operating System

Windows XP Professional or Home Edition (Service Pack 1 or later)

Windows 2000 Professional (Service Pack 4 or later)

Web Browser

Microsoft Internet Explorer 5.01 or greater (recommended)

Available Memory

128 MB (256 MB or greater recommended)

Available Disk Space

225 MB required for installation:
- 160 MB for Microsoft .NET Framework
- 65 MB for Agilent IO Libraries Suite

175 MB required for operation:
- 110 MB for Microsoft .NET Framework
- 65 MB for Agilent IO Libraries Suite

Video

Super VGA (800x600) with 256 colors

Содержание 34945A





























































































































Результаты поиска

Содержание 34945A

Отзывы:

Похожие инструкции для 34945A

Бренды по названию

Популярные бренды

Agilent Technologies 34945A, Руководство пользователя

Результаты поиска

Содержание 34945A

Отзывы:

Похожие инструкции для 34945A

Бренды по названию

Популярные бренды