Agilent Technologies 34945A Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 124

background image

Additional Operating Information

5

Agilent 34945A Microwave Switch/Attenuator Driver Module User’s Guide

109

Note that during a reset, all channel states are actuated resulting in possible
delays during the execution of:

*RST

SYSTem:CPON

ROUTe:RMODule:DRIVe:SOURce

Verifying Switch States

Many switches and attenuators have built-in switch position indicators. The
indicators can be used to drive LED position indicators on the distribution
boards. The 34945A checks the switch position indicator against the SCPI
command last sent to provide verification of the state.

Enabling Verification

Following a preset of any of the distribution boards, electronic verification is
disabled and the switch state is assumed to be the last open/close state driven.
Verification is enabled through the channel configuration window (Chapter 4)
or using the command:

ROUTe:CHANnel:VERify:ENABle

If a switch operation appears to have failed while electronic verification is
enabled, an error is generated at the time either of the commands:

ROUTe:CLOSe

ROUTe:OPEN

is executed. If either of these

commands specify a channel list (i.e., more than

one channel), the verification is performed after all open/close operations
have completed. An error is generated for each channel operation that did not
verify correctly.

With electronic verification enabled, the commands:

ROUTe:CLOSe?

ROUTe:OPEN?

return the actual (verified) hardware state of the specified channel(s), which
may or may not correspond to the programmed state.

Electronic verification of switch position will slow performance of the verified
channels. Additionally, if you have enabled the command overlap function
using the command:

ROUTe:OPERation:OVERlap:ENABle ON

any overlapping is suspended until position verification is complete.

«
...
115
116
117
118
119
...
»

Содержание 34945A





























































































































Отзывы:

Нет отзывов

Похожие инструкции для 34945A

Бренд: Kramer Страницы: 61

Бренд: Cudy Страницы: 2

Бренд: Waters Network Systems Страницы: 12

Бренд: Little Giant Страницы: 2

Бренд: LOVATO ELECTRIC Страницы: 37

SmartNode 4658 Series

Бренд: Patton electronics Страницы: 12

Бренд: Setra Systems Страницы: 4

ExtremeSwitching SLX 9540

Бренд: Extreme Networks Страницы: 108

Бренд: TP-Link Страницы: 28

24-Port Gigabit Switch

Бренд: Belkin Страницы: 2

kontron KSwitch D3 UM

Бренд: S&T Страницы: 38

S3100-16T P-EI-W

Бренд: H3C Страницы: 60

Бренд: Guntermann & Drunck Страницы: 8

ePowerSwitch 8XM Master

Бренд: ADDER Страницы: 2

Бренд: Cambium Networks Страницы: 29

Luzense RADIM RF

Бренд: Unilamp Страницы: 2

Бренд: Veris Industries Страницы: 2

Бренд: ZIEHL-ABEGG Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды