Agilent Technologies 34945A Скачать руководство пользователя страница 114 | Manualshive

Страница: 114 / 124

background image

106

Agilent 34945A Microwave Switch/Attenuator Driver Module User’s Guide

5

Additional Operating Information

Figure 5-6 illustrates the pulse actuation for two channels (switches) and the
relationship of the drive parameters to the power supply requirements.

Figure 5-6. Pulse Actuation Mode Diagram.

As shown in the figure , the actuation pulse is applied to channel 1 and held
for the T(Pulse) time set by the bank

preset

which is 15.0 ms, or as set with the

command:

ROUTe:CHANnel:DRIVe:PULSe:WIDTh

The actuation pulse is applied to channel 2 only after a power supply recovery
period has elapsed T(Recovery). The power supply recovery time can be set for
each channel, and is set to 0.0 ms during a bank

preset

(Chapter 4). The

recovery time can be changed using the command:

ROUTe:CHANnel:DRIVe:TIMe:RECovery

When verifying channel closure, you can also specify a settling time (T(Settle)).
This parameter ensures the switch has had time to change state before the
position indicator (of the switch) is evaluated.

The settling time can be set for each channel and is set to 0.0 ms during a bank

preset

(Chapter 4). The settling time can be changed using the command

ROUTe:CHANnel:DRIVe:TIMe:SETTle

The 34945A will always pulse a channel in response to a

ROUTe:OPEN

or

ROUTe:CLOSe

command. For example, sending

ROUTe:CLOSe

to a channel three

times in a row will result in three actuation pulses.

T(Setttle)

T(Recovery)

Drive Ch 1

Drive Ch2

Start Drive
Channel 1

Start Drive
Channel 2

Channel 1 Position
Indicators Evaluated

T(Pulse)

«
...
112
113
114
115
116
...
»

Содержание 34945A





























































































































Отзывы:

Нет отзывов

Похожие инструкции для 34945A

Бренд: Lantronix Страницы: 40

Бренд: Lantronix Страницы: 2

SISTP1040-551-LRT

Бренд: Lantronix Страницы: 2

Бренд: Lantronix Страницы: 2

SISPM1040-3 L Series

Бренд: Lantronix Страницы: 2

SISPM1040 L3 Series

Бренд: Lantronix Страницы: 36

SecureLinx Spider

Бренд: Lantronix Страницы: 18

Бренд: Lantronix Страницы: 8

Бренд: Lantronix Страницы: 6

SISPM1040-582-LRT

Бренд: Lantronix Страницы: 272

Xpress-Pro SW 52000

Бренд: Lantronix Страницы: 8

Бренд: BERNSTEIN Страницы: 3

Бренд: Z-Band Страницы: 13

Бренд: Guralp Systems Страницы: 22

Бренд: WAGO Страницы: 36

Бренд: rako Страницы: 5

COMMANDE MURALE RTS

Бренд: SOMFY Страницы: 2

Бренд: SMART-AVI Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды