Agilent Technologies 34945A Скачать руководство пользователя страница 58

Страница: 58 / 124

Agilent 34945A Microwave Switch/Attenuator Driver Module User’s Guide

Software Installation and Configuration

Figure 3-8. Adding a VISA Alias for the 34980A.

The Web-Enabled Instrument Interface and Interactive IO

The Web-enabled instrument interface featured in Chapter 4

is not available

from the

GPIB

USB

interface.

For GPIB or USB operation, the Connection Expert ‘Interactive IO’ utility can

be used to send SCPI commands from the 34945A command set to the instru-

ment. See the section “Using Interactive IO” for more information.

Using Interactive IO

The Connection Expert ‘Interactive IO’ utility provides another method (Table

3-1) of sending commands to the 34945A. Similar to the ‘SCPI Command Inter-

face’ window of the web-enabled interface, Interactive IO allows you to send

any command in the 34945A SCPI command set to the instrument. Interactive

IO can be used to:

select and add alias

Содержание 34945A





























































































































Результаты поиска

Содержание 34945A

Отзывы:

Похожие инструкции для 34945A

Бренды по названию

Популярные бренды

Agilent Technologies 34945A, Руководство пользователя

Результаты поиска

Содержание 34945A

Отзывы:

Похожие инструкции для 34945A

Бренды по названию

Популярные бренды