Agilent Technologies 34945A Скачать руководство пользователя страница 49

Страница: 49 / 124

Software Installation and Configuration

Agilent 34945A Microwave Switch/Attenuator Driver Module User’s Guide

Figure 3-1. Product Reference CD-ROM Software (& Driver) Menu.

Install the appropriate driver based on the development environment you are

using.

Accept all default directories specified during installation if

prompted

Setup type “Typical” is applicable for most users.

(As previously

noted, installing the Agilent IO Libraries installs the IVI Shared Components.)

Adding Instruments to the Interface

This section contains information for configuring the 34945A LAN, GPIB, and

USB interfaces using the Agilent IO Libraries ‘Connection Expert’ utility.

Configuring the LAN Interface

With the 34945A turned on and connected to the PC (Chapter 2: Figure 2-1),

start the Connection Expert utility by clicking the ‘IO (control)’ icon and

selecting “Agilent Connection Expert” from the pop up menu as shown in Fig-

ure 3-2.

N O T E

The procedure for using Agilent Connection Expert to locate and configure the
34945A is independent of the type of network you are using (private or site) and
the network devices present (switches or routers).

Figures showing the following Agilent Connection Expert windows represent
Agilent IO Libraries Suite 15.0.

Содержание 34945A





























































































































Результаты поиска

Содержание 34945A

Отзывы:

Похожие инструкции для 34945A

Бренды по названию

Популярные бренды

Agilent Technologies 34945A, Руководство пользователя

Результаты поиска

Содержание 34945A

Отзывы:

Похожие инструкции для 34945A

Бренды по названию

Популярные бренды