Agilent Technologies 34945A Скачать руководство пользователя страница 52

Страница: 52 / 124

Agilent 34945A Microwave Switch/Attenuator Driver Module User’s Guide

Software Installation and Configuration

Figure 3-5. Instruments Found on a Local Subnet.

About IP Addresses and Host names

Dynamic Host Configuration Protocol (DHCP) and Automatic IP are enabled

on the 34980A when shipped from Agilent. This allows the instrument to auto-

matically obtain an address on the network. If there is a DHCP server on the

network, the server will assign the address to the instrument.

If there is not a DHCP server on the network, the 34980A will automatically

determine the address to use. The address will be in the range 169.254.1.1 to

169.254.255.255. If available, the instrument will try to acquire its default set-

ting of 169.254.9.80.

Host Names

The 34980A has a default host name. The format of the host name

is:

A-34980A-yyyyy

where ‘

yyyyy

’ are the last five digits of the instrument’s serial number.

The instrument host name is reported by Agilent Connection Expert for net-

Click to add selected instrument

to the configured interface

Содержание 34945A





























































































































Результаты поиска

Содержание 34945A

Отзывы:

Похожие инструкции для 34945A

Бренды по названию

Популярные бренды

Agilent Technologies 34945A, Руководство пользователя

Результаты поиска

Содержание 34945A

Отзывы:

Похожие инструкции для 34945A

Бренды по названию

Популярные бренды