Aclara SGM3000 Series Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 93

background image

SGM3000 Series Smart Meters

User Manual

Restricted

GEH-7111-1.00-2

11

1

Before You Start

Read and thoroughly understand this guide before installing and operating the unit. Save these
instructions for later use and reference.

Warning: All procedures in this manual must be strictly adhered to. Any

deviation from these could cause irreversible damages to the meter and could lead to
property damage, personal injury, and/or death. Installation and maintenance of the meter
must be carried out by qualified personnel only.

Safety Precautions

Follow all safety precautions and instructions in this manual.

Only qualified personnel should work on the meter. Maintenance personnel should be familiar
with the technology and the hazards associated with electrical equipment.

•

Never

work alone.

•

Before performing visual inspections, tests, or maintenance on this equipment, isolate
or disconnect all hazardous live circuits and sources of electric power. Assume that all
circuits are live until they have been completely de-energized, tested, and tagged. Pay
particular attention to the design of the power system. Consider all sources of power,
including the possibility of back feed.

•

Turn off all power supplying the equipment in which the meter is to be installed before
installing and wiring the meter.

•

Operate only from the power source specified on the installed power supply module.

•

Beware of potential hazards and wear personal protective equipment.

•

The successful operation of this equipment depends upon proper handling, installation,
and operation. Neglecting fundamental installation requirements may lead to personal
injury as well as damage to electrical equipment or other property.

•

All electronic components within the meter are susceptible to damage from
electrostatic discharge. To prevent damage when handling this product use approved
static control procedures.

•

Hazardous voltages can cause shock, burns or death. To prevent exposure to hazardous
voltages, disconnect and lock out all power sources before servicing and removing
components.

«
...
9
10
11
12
13
...
»

Содержание SGM3000 Series






























































































Отзывы:

Нет отзывов

Похожие инструкции для SGM3000 Series

Бренд: Danfoss Страницы: 8

Бренд: Daewoo Страницы: 2

Бренд: Hach Страницы: 145

Бренд: Hach Страницы: 358

Polymetron 9582sc

Бренд: Hach Страницы: 280

Бренд: HACH LANGE Страницы: 15

Бренд: Kathrein Страницы: 10

Бренд: Vaisala Страницы: 90

Бренд: Vaisala Страницы: 4

Бренд: X-Rite Страницы: 50

Бренд: Hama Страницы: 16

Бренд: DriveTest Страницы: 24

Бренд: Mannix Страницы: 5

Бренд: King Instrument Страницы: 5

Бренд: FM Marin Страницы: 8

Thermo Scientific iCE 3000 Series

Бренд: ThermoFisher Scientific Страницы: 42

Бренд: Polimaster Страницы: 24

Бренд: wattwatchers Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды