AccuWeb MICRO 4000 NET Скачать руководство пользователя страница 52

Страница: 52 / 155

Operation:

Discrete Isolated Outputs (DC COMMON is connector J10 terminal 7)

Connector

Output

Description

J10 terminal

This output is

when the actuator has reached the In limit and is

off

during normal operation. This output does not function if a MX-series
actuator is installed.

IN LIMIT

This output is

when the actuator has reached the Out limit and is

off

during normal operation. This output does not function if a MX-series
actuator is installed.

OUT LIMIT

This output is

when the actuator is at the servo-center position and is

off

during normal operation.

SERVO-CENTER

This output is

when the controller is operating in Automatic mode and

off

during all other modes of operation.

AUTO MODE

This output is

when the controller is ready to operate and is

off

when

any of the following conditions occur:

•

The controller is displaying an error code. Refer to page 42 for more
information about error codes.

NO FAULT

•

AC power is off.

•

An edge-loss or line-loss condition occurs. This option is enabled by
setting parameter 47. Refer to page 17 for more information about
setting controller parameters.

This output is controlled by parameter 58. Refer to page 17 for more
information about setting controller parameters.

AUXILIARY

MICRO 4000

NET Controller

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание MICRO 4000 NET




























































































































































Результаты поиска

Содержание MICRO 4000 NET

Отзывы:

Похожие инструкции для MICRO 4000 NET

Бренды по названию

Популярные бренды

AccuWeb MICRO 4000 NET, Инструкция по эксплуатации

Результаты поиска

Содержание MICRO 4000 NET

Отзывы:

Похожие инструкции для MICRO 4000 NET

Бренды по названию

Популярные бренды