AccuWeb MICRO 4000 NET Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 155

background image

Introduction

This document describes the installation and operation of the Fieldbus Interface card. This card
permits a MICRO 4000 NET

control system to communicate with a remote PLC or computer

through a fieldbus network.

Interface cards are available for the most popular fieldbus protocols, including DeviceNet,
Profibus, ControlNet, Modbus Plus, Modbus/TCP, and Ethernet TCP/IP.

The fieldbus interface provides full control of operating mode, guide point position, servo gain,
and actuator speed limit; and permits monitoring of actuator position, end-of-travel status, and
web position.

The fieldbus interface may be used in conjunction with other control inputs. These include the
front-panel switchpad, discrete isolated inputs, and remote operator station. When receiving
commands from multiple sources, the MICRO 4000 NET

obeys the last command received.

The Fieldbus Interface card is compatible only with the MICRO 4000 NET Controller. It is not
compatible with the MICRO 1000 Controller.

Installation

To install the fieldbus interface card in the MICRO 4000 NET controller, follow the steps below:

1. Field installation of the fieldbus interface card in the MICRO 4000 NET Controller:

f) Verify that the power source is

off

and locked out.

g) Install the fieldbus interface card by pushing it firmly onto header P2 on the MICRO 4000

NET

controller assembly.

h) Secure the fieldbus interface card to the standoffs with three #4-40, 0.25” long machine

screws and three #4 internal tooth star washers provided.

Note:

If the control system is ordered with the fieldbus interface card, these components

will be factory installed and tested prior to shipment.

2. Connections and settings:

a) Install the fieldbus interface cable through an available cord grip.

b) Connect the interface cable to the plug for the fieldbus interface card. Configure the card

with the correct network address and baud rate (if required).

c) Insert the plug back into its mating connector on the interface card.

i) Make sure the circuit board is free of metallic debris such as screws, lockwashers, and

wire strands.

d) If any of the cables have been removed, shortened, or modified in any way, make sure

the connections agree with the appropriate connection diagram.

Fieldbus Interface

103

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
104
105
106
107
108
...
»

Содержание MICRO 4000 NET




























































































































































Отзывы:

Нет отзывов

Похожие инструкции для MICRO 4000 NET

Бренд: Zolix Instruments Страницы: 22

Бренд: 2N Страницы: 4

Бренд: CAME Страницы: 18

Бренд: CAME Страницы: 28

Бренд: CAME Страницы: 28

Бренд: CAME Страницы: 4

Бренд: CAME Страницы: 40

Бренд: CAME Страницы: 26

Бренд: CAME Страницы: 34

Бренд: CAME Страницы: 2

Бренд: D+H Страницы: 14

ROBO Cylinder RCP2 Series

Бренд: IAI Страницы: 5

Бренд: National Instruments Страницы: 15

Бренд: National Instruments Страницы: 20

PXI-6683 Series

Бренд: National Instruments Страницы: 4

Бренд: National Instruments Страницы: 22

NI PXI-665 Series

Бренд: National Instruments Страницы: 14

Бренд: National Instruments Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды