AccuWeb MICRO 4000 NET Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 155

AccuWeb MICRO 4000 NET Скачать руководство пользователя страница 38

6

3

2

This mode is used for stabilizing the response of guides that have
sensors located downstream. The downstream sensors are connected to
Integrator Input 1 and 2 and the local sensors are connected to Input A,
B, and C. During operation the integrator output slowly changes the local
guide point as long as the downstream sensors indicate that the web is
not at the downstream guide point.

Note:

This mode is available only if the integrator option is installed.

Contact AccuWeb for availability.

6

3

3

This mode is used for dampening the response of the slave guide in
chaser-slave systems. The chaser sensors are connected to Integrator
Input 1 and 2 and the slave sensors are connected to Input A, B, and C.
During operation the chaser sensors establish the slave guide point, but
the integrator dampens noise and jitter in the chaser signal.

Integrator Input 1 Type

This parameter selects the source for Integrator Input 1.

6

4

0

No input (zero).

6

4

1

Sensor 1.

6

4

2

Sensor 2.

This is the default setting.

6

4

3

Digital line guide.

6

4

4

Analog Input 1 (scaled by parameters 43 and 44).

6

4

5

Analog Input 2 (scaled by parameters 45 and 46).

Integrator Input 2 Type

This parameter selects the source for Integrator Input 2.

6

5

0

No input (zero).

This is the default setting.

6

5

1

Sensor 1.

6

5

2

Sensor 2.

6

5

3

Digital line guide.

[continued on next page]

MICRO 4000

®

NET Controller

35

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
36
37
38
39
40
...
»

Содержание MICRO 4000 NET




























































































































































Отзывы:

Нет отзывов