AccuWeb MICRO 4000 NET Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 155

background image

Appendix 3 / Oscillation Function (Optional)

This optional software feature allows the user to perform web oscillation electronically, thus
replacing the mechanical hardware normally required for this function.

Web oscillation is primarily used for processing materials that need oscillation to reduce
gauge-band build-up on re-wind rolls.

Web oscillation is accomplished by electronically moving the guide point to oscillate the web over
a wide range of speeds and travel distance. The oscillation speed and travel can be programmed
within the following ranges:

•

Oscillation speed:

0 to 25.5 inches per minute

•

Oscillation travel:

0 to 7.50 inches (or

±

linear actuator stroke)

When the oscillation function is turned off the guide point is fixed. The system moves the web as
needed to keep the web’s edge or centerline aligned with the fixed guide point.

When the oscillation function is turned on the guide point moves at a programmed speed over a
programmed travel distance. The system moves the web continuously to keep the web’s edge or
centerline aligned with the moving guide point.

The AUXILIARY input can be used to turn the oscillation function on and off (parameter 52, option
3 or 4).

The rate of oscillation can also be controlled by the analog inputs (parameter 31, option 2 or 3). In
this mode the oscillation rate is proportional to input voltage. When the input voltage is at the
lowest end of its range, the oscillation rate will be at its minimum value (set by parameter 53).
When the input voltage is at the highest end of its range, the oscillation rate will be at its highest
value (set by parameter 33).

An additional oscillation mode (parameter 31, option 4) permits oscillation without using an edge
sensor. This mode continuously oscillates the actuator between its In and Out end-of-travel limits.
Oscillation speed is controlled by parameter 7, or by an external analog (parameter 48, option 2
or 3) or fieldbus input (parameter 48, option 1). If using an actuator that has potentiometer
feedback (MT, SF, HL, HF, HT, and UHT) the oscillation distance may be adjusted by setting the
In and Out end-of-travel limits (parameters 9 and 10). Oscillation distance is fixed for actuators
that have limit switches (MM, MME, MN, and MNE). MX-series actuators do not operate in this
oscillation mode.

Note:

Refer to page 17 for more information about setting controller parameters.

MICRO 4000

®

NET Controller

43

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
44
45
46
47
48
...
»

Содержание MICRO 4000 NET




























































































































































Отзывы:

Нет отзывов

Похожие инструкции для MICRO 4000 NET

Бренд: Samson Страницы: 48

Бренд: Mako Networks Страницы: 15

Бренд: Samson Страницы: 36

Бренд: FBII Страницы: 71

Бренд: CAME Страницы: 4

Бренд: Panasonic Страницы: 5

Бренд: Panasonic Страницы: 14

Бренд: Panasonic Страницы: 2

Harmony Controller 2000

Бренд: A10 Страницы: 27

Бренд: Sanhua Страницы: 3

Бренд: rav Страницы: 120

Бренд: Lawler Страницы: 5

Бренд: Parker Страницы: 32

Бренд: Rayrun Страницы: 4

AeGIS 7000 Series

Бренд: PACH & COMPANY Страницы: 2

Бренд: OMC Страницы: 18

Бренд: Paradox Страницы: 2

Бренд: Paradox Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды