AccuWeb MICRO 4000 NET Скачать руководство пользователя страница 44

Страница: 44 / 155

Integrator input offset

0-2

AUXILIARY and INHIBIT input config

0, 1

Integrator rate multiplier

0-2

Sensor A transducer orientation

0, 1

Sensor B transducer orientation

0, 1

Sensor A reduced length

2-128

Sensor B reduced length

2-128

Fieldbus swap bytes

0, 1

These parameters are used for monitoring system functions and cannot be changed through the

programming keypad.

These parameters are used for calibrating the edge detectors.

These parameters are primarily used for monitoring system functions, but can be changed

through the programming keypad.

These parameters are used for installing optional features such as oscillation, web width

monitoring and integration. Contact AccuWeb for availability.

These parameters function only if the oscillation option is installed. Contact AccuWeb for

availability.

Option 2 is available only if the integrator option is installed. Contact AccuWeb for availability.

MICRO 4000

NET Controller

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание MICRO 4000 NET




























































































































































Результаты поиска

Содержание MICRO 4000 NET

Отзывы:

Похожие инструкции для MICRO 4000 NET

Бренды по названию

Популярные бренды

AccuWeb MICRO 4000 NET, Инструкция по эксплуатации

Результаты поиска

Содержание MICRO 4000 NET

Отзывы:

Похожие инструкции для MICRO 4000 NET

Бренды по названию

Популярные бренды