AccuWeb MICRO 4000 NET Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 155

background image

Operation

The MICRO 4000 NET

may be configured for a wide variety of applications, but most

configurations share the same basic operating procedure:

1) Press the SERVO-CENTER button and wait for the web guide to drive to the center of travel.

2) Thread the web through the machine.

3) Position the sensors.

One edge detector:

Place the detector near the edge of the web. Move the detector towards

the web until its null indicator LED turns off.

Note:

The scribed lines on the edge detector

indicate the approximate location of the detector’s guide point.

Two edge detectors (centerline guiding):

Press the EDGE A button. Place detector A near

the edge of the web. Move detector A towards the web until its null indicator LED turns off.
Press the EDGE B button. Place detector B near the opposite edge of the web. Move
detector B towards the web until its null indicator LED turns off.

Note:

The scribed lines on

the edge detector indicate the approximate location of the detector’s guide point.

Digital line guide:

Position the sensor so that it is approximately centered over the

registration line or edge. When it is positioned correctly an indicator dot will appear in the
display under the line or edge you want to track. Refer to page 60 for more information about
operating the line guide.

4) Press the EDGE A, EDGE B, or LINE button. For Centerline mode (centerline guiding), press

the EDGE A and EDGE B buttons simultaneously.

5) Press the AUTOMATIC button. The system will now guide the web.

Scribe mark

Scribe marks

Null indicator

Null indicator

Move detector until

null

indicator

turns

off

Web

Web

PointSource

detector

WideArray

detector

Centerline guiding with WideArray detectors

MICRO

4000

®

NET

Web Guide Control System

10

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
11
12
13
14
15
...
»

Содержание MICRO 4000 NET




























































































































































Отзывы:

Нет отзывов

Похожие инструкции для MICRO 4000 NET

Бренд: Eaton Страницы: 166

SolarCell Remote

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 20

Бренд: Harman Kardon Страницы: 25

Бренд: Uniss Страницы: 21

Бренд: Laser Страницы: 2

Бренд: LAS Страницы: 6

Бренд: Lars Thrane Страницы: 141

Бренд: Wang Страницы: 68

Бренд: NAVITAS Страницы: 14

Бренд: J+J Страницы: 4

Бренд: Val Controls Страницы: 6

Бренд: Jetter Страницы: 24

Бренд: Challenger Lifts Страницы: 20

Бренд: Mitsubishi Страницы: 16

Бренд: SOMFY Страницы: 4

Бренд: micro-trak Страницы: 44

GECO LUX GECO60

Бренд: GiBiDi Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды