AccuWeb MICRO 4000 NET Скачать руководство пользователя страница 33

Страница: 33 / 155

Servo Gain and Speed Limit Source

Servo Gain is controlled by parameter 5.

Auto-Mode Speed Limit is controlled by parameter 7.

This is the default setting.

Servo Gain and Auto-Mode Speed Limit are controlled by the optional
Fieldbus Interface (page 102).

Servo Gain is controlled by Analog Input 1.

Auto-Mode Speed Limit is controlled by parameter 7.

Servo Gain is controlled by parameter 5.

Auto-Mode Speed Limit is controlled by Analog Input 1.

Input C Type

Sensor C is not installed.

This is the default setting.

Sensor C is an ultrasonic or IR edge detector connected to the Edge
Detector A input.

Note:

Set parameter 55 to select sensor type.

Sensor C is a digital line guide connected to the Serial I/O interface.

Sensor C is an external analog device connected to Analog Input 1.

Note:

In order to select Input C through the front-panel switchpad, fieldbus, or Discrete Isolated

Inputs, parameter 49 must be set to 1 or higher.

Input C Polarity

The actuator will move Out when edge detector A is

unblocked

, or the

digital line guide’s sight point is to the

left

of the line or edge it is

following.

This is the default setting.

The actuator will move Out when edge detector A is

blocked

, or the

digital line guide’s sight point is to the

right

of the line or edge it is

following.

MICRO 4000

NET Controller

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание MICRO 4000 NET




























































































































































Результаты поиска

Содержание MICRO 4000 NET

Отзывы:

Похожие инструкции для MICRO 4000 NET

Бренды по названию

Популярные бренды

AccuWeb MICRO 4000 NET, Инструкция по эксплуатации

Результаты поиска

Содержание MICRO 4000 NET

Отзывы:

Похожие инструкции для MICRO 4000 NET

Бренды по названию

Популярные бренды