AccuWeb MICRO 4000 NET Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 155

background image

Switchpad Type

5

1

0

Select this option if the input selection buttons on the front-panel
switchpad are labeled EDGE A, CENTERLINE, and EDGE B.

The EDGE A button selects Input A.

The EDGE B button selects Input B.

The CENTERLINE button selects Inputs A and B.

This switchpad does not allow the selection of Input C.

5

1

1

Select this option if the input selection buttons on the front-panel
switchpad are labeled EDGE A, EDGE B, and LINE.

The EDGE A button selects Input A.

The EDGE B button selects Input B.

The LINE button selects Input C.

To select Centerline mode, press the EDGE A and EDGE B buttons
simultaneously.

5

1

2

Front-panel switchpad operation is the same as option 1.

Bit 7 of the fieldbus Operating Mode Command word selects Automatic
mode. Refer to page 102 for more information about the Fieldbus
Interface.

This is the default setting.

Note:

This parameter also affects the operation of the Discrete Isolated Inputs (page 46).

AUXILIARY Input Function

for more information about the AUXILIARY input.

Refer to page 46

5

2

0

The AUXILIARY input is off.

This is the default setting.

5

2

1

The AUXILIARY input determines which offset is active. To select Offset
2, activate the AUXILIARY input. To select Offset 1, deactivate the
AUXILIARY input.

5

2

2

Same function as option 1, except the polarity of the AUXILIARY input is
inverted.

5

2

3

Activating the AUXILIARY input will enable Oscillation, and deactivating
it will disable Oscillation. Oscillation parameter 31 must be set to 1 or
higher.

Refer to page 43 for more information about the oscillation function.

5

2

4

Same function as option 3, except the polarity of the AUXILIARY input is
inverted.

5

2

5

Activating the AUXILIARY input will switch the system to Automatic
mode.

5

2

6

Same function as option 5, except the polarity of the AUXILIARY input is
inverted.

[continued on next page]

MICRO 4000

®

NET Controller

31

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
32
33
34
35
36
...
»

Содержание MICRO 4000 NET




























































































































































Отзывы:

Нет отзывов

Похожие инструкции для MICRO 4000 NET

Бренд: Farris Engineering Страницы: 12

Бренд: Eastern Times Technology Страницы: 4

Бренд: Vacon Страницы: 18

Бренд: Zolix Instruments Страницы: 22

Бренд: Bang & Olufsen Страницы: 80

Бренд: Bang & Olufsen Страницы: 13

Бренд: Racal Instruments Страницы: 94

Бренд: Racal Instruments Страницы: 97

Бренд: Magellan Страницы: 44

Бренд: Namron Страницы: 3

Бренд: Parker Страницы: 32

Бренд: Rayrun Страницы: 4

AeGIS 7000 Series

Бренд: PACH & COMPANY Страницы: 2

Бренд: RadioMaster Страницы: 49

SUPERREMOTE UR19A

Бренд: X10 Страницы: 3

Бренд: Xantech Страницы: 102

Бренд: Xantech Страницы: 17

Бренд: X10 Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды