AccuWeb MICRO 4000 NET Скачать руководство пользователя страница 66

Страница: 66 / 155

Operation

This section describes the Digital Line Guide’s front panel keys and display, and outlines a basic
operating procedure.

Display:

•

The 2-line LCD display is divided into four fields as shown:

PARAMETER VALUE

GRAPHIC DISPLAY

CONTRAST

PARAMETER field: Name of the currently selected parameter.

VALUE field: Value of the currently selected parameter.

GRAPHIC DISPLAY field: Graphically displays what is in the sensor’s field of view.

CONTRAST field: Contrast value of the highest contrast edges in the sensor’s field of view.

•

The parameters are described in the Parameters section of this manual (page 71).

•

At power-up, a software identification message is displayed for several seconds then the

display reverts to the format described above:

A c c u B e a m

D L G

x x . x x

Front panel keys:

•

The front panel keys are defined as follows:

UP DOWN

ENTER

•

To select a parameter press the ENTER key until the cursor is in the PARAMETER field, then
press the UP

or DOWN

keys until the desired parameter is displayed.

•

To change a parameter’s value press the ENTER key until the cursor is in the VALUE field,
then press the UP

or DOWN

keys until the desired value is displayed.

•

The keys automatically repeat if held down for more than one second.

Operation:

1) Press the SERVO-CENTER button and wait for the guide to move to its center of travel.

2) Thread the web through the machine.

3) Press the EDGE A, EDGE B, or LINE button.

4) Align the sensor with the line or edge to be tracked on the web material.

5) If this is the first time you are running this particular web material, perform the auto-calibration

procedure described in the Calibration section of this manual (page 65).

AccuBeam 3 Digital Line Guide Sensor

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание MICRO 4000 NET




























































































































































Результаты поиска

Содержание MICRO 4000 NET

Отзывы:

Похожие инструкции для MICRO 4000 NET

Бренды по названию

Популярные бренды

AccuWeb MICRO 4000 NET, Инструкция по эксплуатации

Результаты поиска

Содержание MICRO 4000 NET

Отзывы:

Похожие инструкции для MICRO 4000 NET

Бренды по названию

Популярные бренды