manualshive.com logo in svg

AccuWeb MICRO 4000 NET, Инструкция по эксплуатации, Страница: 15 / 155

Поделиться
Скачать
AccuWeb MICRO 4000 NET Скачать руководство пользователя страница 15

INHIBIT input polarity is set wrong.

 Set parameter 19 to the correct 

value. Refer to page 

4 

17 for more information about setting controller 

parameters. 

5 

New software was installed during routine maintenance. 

or 

Non-volatile memory contains invalid data or has malfunctioned. 

Reset all parameters to their default values: 

Caution: 

This procedure will erase all previously entered parameter 

settings! Be sure to record all current settings on page 39 before 
performing this step. If you are installing new software, then you must 
record the current settings 

before

 installing the new microcontroller 

chip.

 

1.  Turn the AC power 

off

. 

2.  Press and hold the EXIT button. 

3.  Turn the AC power 

on

. 

4.  When the ‘reset’ message appears on the numeric display, release the 

EXIT button. 

5.  Set parameter 2 (end-of-travel mode) and other parameters to their 

previous values. Refer to page 17 for more information about setting 
controller parameters. 

Sensor polarity is wrong.

 The value of parameter 3, 4, or 50 must be 

changed for the selected sensor. Refer to page 

6 

17 for more information 

about setting controller parameters. 

Servo gain is too high.

 Decrease the value of parameter 5. Refer to page 

7 

17 for more information about setting controller parameters. 

End play in the actuator or mounting.

 Press the MANUAL button and 

then press IN and OUT buttons several times. Actuator operation should be 
smooth and free, without binding. Firmly grasp the web guide mechanism 
moving part and push and pull to check for end play. Observe the actuator, 
mechanical components, and mounting hardware. There should be no 
observable motion in the mechanical system. If motion is noted, repair the 
web guide or actuator as required, or return the equipment for repair. 

8 

9 

Sensor in wrong position. 

Unwind stand: 

The sensor should be located down-web, close to the last 

shifting idler roll. Refer to the guide application drawings on page 137. 

Winder stand: 

The sensor should be located up-web before the last fixed 

idler roll, one to two web widths from the shifting base. Refer to the guide 
application drawings on page 137. 

Intermediate guides: 

The sensor should be placed close to the exiting 

idler roll. Refer to the guide application drawings on page 137. 

Excessive chuck wobble.

 Decrease the web speed or re-chuck the roll of 

material. 

10 

Web tension is low or tension control varies.

 Increase the web tension 

or repair the tension control. 

11 

 MICRO 

4000

®

 NET

 

Web Guide Control System 

12 

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание MICRO 4000 NET




























































































































































Отзывы:

Нет отзывов