AccuWeb MICRO 4000 NET Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 155

background image

e) Press the EDGE A, EDGE B, or LINE button to select the sensor under test.

f) Press the AUTOMATIC button.

g) Slowly move the sensor left or right and observe how the guide reacts. The guide should

move the web so that it follows (or chases) the movement of the sensor.

Edge detector:

The guide should move the web so that the edge of the web is always

aligned with the edge detector’s guide point.

Digital line guide:

The guide should move the web so that the line or edge pattern is

always aligned with the line guide’s sight point.

Note:

If the guide does not follow the movement of the sensor and moves in the opposite

direction, then the sensor polarity (parameters 3, 4, or 50) is not correct and must be
changed. Refer to page 17 for more information about setting controller parameters.

h) If the guide mechanism oscillates around the guide point or overshoots excessively when

steering in response to an abrupt change in web position, the servo gain (parameter 5) is
too high and must be lowered. Refer to page 17 for more information about setting
controller parameters.

MICRO

4000

®

NET

Web Guide Control System

9

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
10
11
12
13
14
...
»

Содержание MICRO 4000 NET




























































































































































Отзывы:

Нет отзывов

Похожие инструкции для MICRO 4000 NET

Бренд: Gardena Страницы: 100

Бренд: IBM Страницы: 72

Бренд: Yudian Страницы: 26

Tissue-Tek TEC 6

Бренд: Sakura Seiki Страницы: 6

Бренд: Vacon Страницы: 50

Бренд: V2 Страницы: 116

Бренд: V2 Страницы: 8

Бренд: V2 Страницы: 25

Бренд: V2 Страницы: 124

Бренд: V2 Страницы: 12

NORA-W10 Series

Бренд: u-blox Страницы: 56

Бренд: z21 Страницы: 2

Бренд: cinetto Страницы: 56

Бренд: Gardigo Страницы: 6

Бренд: VAT Страницы: 14

Бренд: Dakota Digital Страницы: 12

Бренд: K&K Страницы: 10

Бренд: DSEGenset Страницы: 74

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды