Accutrol AccuValve AVR6000 Скачать руководство пользователя страница 57

Страница: 57 / 61

Installation & Operation Manual - Model AVR6000

The

ADS Room Temperature Sensor

is installed in the return or general exhaust air duct that is

serving the room that is being controlled by the AVR6000. The ADS is provided with 2 self-

drilling sheet metal screws for securing to the return air or general exhaust duct.

ADS1x

Model Code

NOTE:

Each ARS or ADS is shipped with a factory prefabricated plenum-rated cable for connecting directly

to the AVR6000 control module. The ARS1 type is configured using the AccuValve Insight Software. All

configuration parameters are stored in the AVR6000 control module and can be accessed using the

AccuValve Insight Configuration Software.

NOTE:

The ADS1 does not have a USB port, therefore connection to the configuration PC must be done by

connecting to the USB port located on the AVR6000 or by using Bluetooth if the AVR6000 includes the

wireless option.

Содержание AccuValve AVR6000






























































Результаты поиска

Содержание AccuValve AVR6000

Отзывы:

Бренды по названию

Популярные бренды

Accutrol AccuValve AVR6000, Руководство по установке и эксплуатации

Результаты поиска

Содержание AccuValve AVR6000

Отзывы:

Бренды по названию

Популярные бренды