manualshive.com logo in svg

Accutrol AccuValve AVR6000, Руководство по установке и эксплуатации

Поделиться
Скачать
Accutrol AccuValve AVR6000 Скачать руководство пользователя страница 38

Installation & Operation Manual - Model AVR6000 

Contents of this Manual are Subject to Change Without Notification

 

Page   38 

6.5.3.3 AVR Dashboard Menus 

The area located along the top of Dashboard provides access to the menu items on the 

left side and valve information such as MAC Address, Tag, Operating Mode and USB com 

status on the right side. Each menu item is described in the following sections. 

 

 

6.5.3.3.1

 

File Menu Items 

6.5.3.3.1.1

 

Load 

 

From Controller Flash Memory

 loads config file that resides in the AVR nonvolatile 

memory (FLASH) into the AVR volatile memory (RAM).

 

From Configuration File

 loads the config file that resides in a nonvolatile storage 

device (i.e. hard drive or USB Flash Drive) into the AVR volatile memory (RAM). 

 CAUTION

: This selection will load Configuration Settings and Calibration Data, 

which is valve size specific. When using this function, make sure to load only a 

factory provided file that is intended for that specific valve (based on duct size, 

actuator type, etc). 

Restore Factory Defaults 

loads the original factory config file that resides in a 

protected portion of the AVR nonvolatile memory (FLASH) to the AVR volatile 

memory (RAM). 

 

 

 

 

Содержание AccuValve AVR6000






























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды