Accutrol AccuValve AVR6000 Скачать руководство пользователя страница 54

Страница: 54 / 61

Installation & Operation Manual - Model AVR6000

Contents of this Manual are Subject to Change Without Notification

Page 54

SECTION 9 - MAINTENANCE

Scheduled maintenance for the AVR is not required; however, each AccuValve does include an

access cover which can be removed to inspect the airflow sensors if desired.

9.1 Round Valve Access Cover

CAUTION:

Wear eye protection, cut-resistant gloves, and clothing suitable for working

with sheet metal. Failure to do so may result in personal injury.

9.1.1 Loosen the 3/8” bolt enough to allow the access door to slide forward.

CAUTION:

If the bolt is removed from the captive nut, the access cover can spring open

possibly causing injury.

9.1.2 Using two hands; squeeze the access

cover and slide it forward over the valve

enough to uncover the access opening.

9.1.3 Once the cover is slid forward or

removed, the airflow sensors can be visually

inspected.

9.1.4 When inspection is complete, slide the

access cover over the opening, being careful

not to damage gasket in the process.

9.1.5 Verify the access cover is in position to

completely cover the opening. Secure cover in place by tightening the 3/8” bolt using care not

to over tighten.

Access Cover

Loosen

3/8” Bolt

Sensors

Содержание AccuValve AVR6000






























































Результаты поиска

Содержание AccuValve AVR6000

Отзывы:

Бренды по названию

Популярные бренды

Accutrol AccuValve AVR6000, Руководство по установке и эксплуатации

Результаты поиска

Содержание AccuValve AVR6000

Отзывы:

Бренды по названию

Популярные бренды