Accutrol AccuValve AVR6000 Скачать руководство пользователя страница 56

Страница: 56 / 61

Installation & Operation Manual - Model AVR6000

APPENDIX A - ARS & ADS Room Temperature Sensors

There are two different Accutrol devices that can be used to obtain the room temperature

measurement with the AVR6000 control system. The most common device used is the ARS

room temperature sensor which is a wall-mount unit that is installed inside of the room which

is being controlled. For applications that do not allow wall-mount devices to be installed inside

of the controlled room, the ADS, which is a duct-mount return air temperature sensor is used.

A brief description of each room temp sensor device is provided in this section. For a detailed

description of each device, reference the Accutrol submittal drawings.
The

ARS Room Temperature Sensor

shall be installed inside of the room that is being

controlled in a location where the temperature and RH is that is not effected by drafts from

door ways, supply diffusers, equipment or direct sunlight. The ARS is provided with 2 mounting

screws for securing to a standard single-gang electrical box on the wall within the room.

4.8"

121.9mm

3.0"

76.2mm

USB Configiguration Port

Temp. Setpoint Adjust Slider

(Optional)

User Configurable Display

(Optional)

73.5

Motion Sensor

(Optional with ARS2)

RJ45 Port for

Factory Cable

Connection to

AVR Control

Module

1.26“ 32mm

1.0“ 25.4mm

Model Code

1 - 25' Cable

2 - 50' Cable

3 - 75' Cable

4 - 100' Cable

ARS

1 - Room Temp

2 - Room Temp & Relative Humidity

Sensor Type

Blank - No Options

D – Display

M - Motion Sensor

S - Slider Adjust

Options

Cable Length

(ARS2 Model Only)

LCD Display (Optional)

Type: Character Liquid Crystal Display, 2 Lines x 8 Characters with White LED Backlight

Indicates room temperature, RH, Active Mode, and includes heating and cooling icons. Range

of displayed temperature is 0.5 to 99.5 degrees F.

Configuration Port

USB Type C Protected by Removable Rubber Plug at base of unit. Provided for connecting PC

with the AccuValve Insight Configuration Software.

Содержание AccuValve AVR6000






























































Результаты поиска

Содержание AccuValve AVR6000

Отзывы:

Бренды по названию

Популярные бренды

Accutrol AccuValve AVR6000, Руководство по установке и эксплуатации

Результаты поиска

Содержание AccuValve AVR6000

Отзывы:

Бренды по названию

Популярные бренды