Xerox Phaser 7300 Study Manual Download Page 46

Page: 46 / 68

page 42

PHASER 7300 Troubleshooting Flowcharts

Customer Replaceable Consumables

Stop printer
during print

cycle and

remove

Fuser.

Note: Before troubleshooting, make
sure a supported media is used for
printing and that the media is free of
damage such as wrinkles, tears, and
curl. Make sure the printer
environment is within specifications
for humidity and temperature.

Unfused Toner on Prints

Yes

Call for service.

Does sheet

slip between

rollers?

Replace the

Fuser.

Still unfused

toner?

Problem solved.

Try to slip a

sheet of

paper

between the

Fuser rollers.

Check for debris,

paper or

contamination on

or wrapped

around Fuser

roller.

Yes

Rollers

contaminated or

wrapped?

Yes

Still unfused

toner?

Problem solved.

Set Front

Panel media

type to next

heaviest type

of paper.

Summary of Contents for Phaser 7300





































































Search results

Summary of Contents for Phaser 7300

Reviews:

Related manuals for Phaser 7300

Brands by name

Popular brands

Xerox Phaser 7300, Study Manual

Search results

Summary of Contents for Phaser 7300

Reviews:

Related manuals for Phaser 7300

Brands by name

Popular brands