Xerox Phaser 7300 Study Manual Download Page 53

Page: 53 / 68

PHASER 7300 Troubleshooting Flowcharts

page 49

Jams

Note: Before troubleshooting, make
sure a supported media is used for
printing and that the media is free of
damage such as wrinkles, tears, and
curl. Make sure the printer
environment is within specifications
for humidity and temperature.

Jam at Top Cover, A6 or A22

Yes

Problem solved.

Printing normally?

Problem solved.

Media

around Transfer

Unit?

Reseat the

Transfer Unit.

Remove

media and

scraps from

around the

Transfer Unit.

Still jamming?

Check for

jammed

media around

the Transfer

Unit.

Call for service.

Problem solved.

Replace the

Transfer Unit.

Still jamming?

Yes

Feeding

from Universal

Tray?

Ensure Front

Panel media

type is

correct.

Yes

Is media type

correct?

Set media type and

retest.

Is media

partially fed?

Clean the MPT Feed

Roller and retest.

Yes

Summary of Contents for Phaser 7300





































































Search results

Summary of Contents for Phaser 7300

Reviews:

Related manuals for Phaser 7300

Brands by name

Popular brands

Xerox Phaser 7300, Study Manual

Search results

Summary of Contents for Phaser 7300

Reviews:

Related manuals for Phaser 7300

Brands by name

Popular brands