Xerox Phaser 7300 Study Manual Download Page 25

Page: 25 / 68

PHASER 7300

English

PHASER 7300 CARE WORKSHEET

page 21

Prerequisites

❑

Care section

Equipment Checklist

❑

Phaser 7300 Laser
Printer

❑

Lint-free cloth for
cleaning the LED
assemblies

❑

Light-proof, black,
plastic bag to protect
the Print Cartridge

❑

Phillips Screwdriver

References

Electronic copies of all
manuals and instruction
sheets are located on the

Phaser 7300 Color Laser
Printer Interactive
Documentation CD-ROM

Click the training module's

Resources

link to access

the manuals and instruction
sheets.

Time to complete

❑

60 minutes

Objectives

■

Replace consumables

■

Reset consumable counts

■

Troubleshoot media jams

■

Solve print quality problems

Replace Consumables

During this step of the worksheet, you will examine, remove, troubleshoot,
and replace consumables that are used during normal operation. The Phaser
7300 printer is designed modularly for easy maintenance. There are ten
consumable supplies:

■

Toner Cartridges (cyan, magenta, yellow, black)

■

Imaging Units (cyan, magenta, yellow, black)

■

Fuser

■

Transfer Unit

Refer to the following pages of this worksheet for detailed
instructions to complete each objective listed above.

Fuser

Transfer Unit

Toner Cartridges (4)

Imaging Units (4)

CARE WORKSHEET

Summary of Contents for Phaser 7300





































































Search results

Summary of Contents for Phaser 7300

Reviews:

Related manuals for Phaser 7300

Brands by name

Popular brands

Xerox Phaser 7300, Study Manual

Search results

Summary of Contents for Phaser 7300

Reviews:

Related manuals for Phaser 7300

Brands by name

Popular brands