Xerox Phaser 7300 Study Manual Download Page 54

Page: 54 / 68

page 50

PHASER 7300 Troubleshooting Flowcharts

Jams

Note: Before troubleshooting, make
sure a supported media is used for
printing and that the media is free of
damage such as wrinkles, tears, and
curl. Make sure the printer
environment is within specifications
for humidity and temperature.

Jam at Top Cover, A7 or A10

Yes

Still jamming?

Yes

Call for service.

Paper or

scraps in Fuser

area?

Check for

jammed paper

and scraps in

the Fuser.

Ensure Fuser

locking levers

are fully
latched.

Problem solved.

Printing normally?

Problem resolved.

Replace the

Fuser.

Open the

Left Side

Output Tray

and print the

job.

Still jamming?

Remove any

paper or

scraps from

the Fuser

area.

Make sure

Left Side

Output Tray is

completely

closed.

Close tray if

necessary.

Problem solved.

Summary of Contents for Phaser 7300





































































Search results

Summary of Contents for Phaser 7300

Reviews:

Related manuals for Phaser 7300

Brands by name

Popular brands

Xerox Phaser 7300, Study Manual

Search results

Summary of Contents for Phaser 7300

Reviews:

Related manuals for Phaser 7300

Brands by name

Popular brands