Xerox Phaser 7300 Study Manual Download Page 20

Page: 20 / 68

page 16

PHASER 7300 SETUP WORKSHEET

version 1.0

Network Connection

This worksheet provides instructions for installing the PostScript driver for Windows 98.

The printer should be connected to the network, turned on, online, and ready to print.

Insert the

Phaser 7300 Printer Installer and Utilities CD-ROM

into your PC; the

installation setup program will auto-launch.

Click

Install Printer Driver

to begin the installation process. The setup program will

launch the Printer Installation Wizard.

Read the license agreement, then click OK.

The wizard scans the parallel, USB, and network ports to locate a printer.

Automatic Install is the default installation option when more than one Phaser printer is
detected on the network. This option is also available when only one printer is detected.
Verify that

Automatic Install

is selected, then click

Next

Read the installation instructions. First, walk over to the printer and find the Front
Panel display.

Second, use the down arrow key to highlight

Printer Identification

, then press

Third, highlight

Select For Installation

, then press

Once the Installer detects the printer, it automatically installs the driver on
the computer.

10.

Upon completion of the driver installation, two options are available.

■

Information Forwarding

allows the printer to periodically send information to Xerox

for use with PhaserSMART, such as firmware version, serial number, and page count.

■

Register your printer

provides Web, email, modem, fax, and standard mail options for

registration.

11.

Click

Finish

to continue.

12.

Next, the

Registration Wizard

launches. This installation assumes the printer is

already registered; click

Cancel

13.

Finally, click

Never Register

to access the exit CD Screen.

14.

To view the driver configuration, click the Windows

Start

button.

15.

Roll your cursor over

Settings

, and click

Printers

to display the

Printers

folder.

To use the peer-to-peer print monitor, the printer and computer must have
valid TCP/IP addresses, and they must be on the same network.

Summary of Contents for Phaser 7300





































































Search results

Summary of Contents for Phaser 7300

Reviews:

Related manuals for Phaser 7300

Brands by name

Popular brands

Xerox Phaser 7300, Study Manual

Search results

Summary of Contents for Phaser 7300

Reviews:

Related manuals for Phaser 7300

Brands by name

Popular brands