Xerox Phaser 3310 User Manual Download Page 124

Page: 124 / 200

ROBLEM

OLVING

Problem

Solution

Character voids are white areas within the parts of
characters that should be solid black:

• If you are using transparencies when you experience this

problem, try another type of transparency. (Because of the
composition of transparency media, some character voids
are normal.)

• You may be printing on the wrong surface of the paper.

Remove the paper and turn it around.

• The paper may not meet paper specifications. See “Paper

Specifications” on

page A.2

Character Voids

• Clean the inside of the printer.

• Check the paper type and quality. See “Paper

Specifications” on

page A.2

• Try installing a new toner cartridge.

• If the problem persists, the printer may require repairs.

Contact a service representative.

Loose toner

If horizontally aligned black streaks or smears appear:

• The toner cartridge may be installed improperly. Remove

the cartridge and reinsert it.

• The toner cartridge may be defective. Install a new toner

cartridge.

• If the problem persists, the printer may require repairs.

Contact a service representative.

Horizontal stripes

AaBbCc
AaBbCc
AaBbCc

AaBbCc

AaBbCc
AaBbCc
AaBbCc

AaBbCc
AaBbCc

AaBbCc
AaBbCc
AaBbCc

AaBbCc

AaBbCc
AaBbCc
AaBbCc

AaBbCc
AaBbCc

AaBbCc
AaBbCc
AaBbCc

AaBbCc
AaBbCc

AaBbCc
AaBbCc
AaBbCc

AaBbCc

AaBbCc
AaBbCc
AaBbCc

AaBbCc
AaBbCc

Solving Print Quality Problems

Summary of Contents for Phaser 3310









































































































































































































Search results

Summary of Contents for Phaser 3310

Reviews:

Related manuals for Phaser 3310

Brands by name

Popular brands

Xerox Phaser 3310, User Manual

Search results

Summary of Contents for Phaser 3310

Reviews:

Related manuals for Phaser 3310

Brands by name

Popular brands