Xerox Phaser 3310 User Manual Download Page 123

Page: 123 / 200

ROBLEM

OLVING

Problem

Solution

• Check the paper type and quality. Both high temperature

and humidity will cause paper curl. See “Paper
Specifications” on

page A.2

• Turn over the stack of paper in the paper tray. Also try

rotating the paper 180° in the paper tray.

• Open the rear output tray and try printing to the face up

output tray.

Curl or wave

• Make sure that paper is loaded properly.

• Check the paper type and quality. See “Paper

Specifications” on

page A.2

• Open the rear output tray and try printing to the face up

output tray.

• Turn over the stack of paper in the paper tray. Also try

rotating the paper 180° in the tray.

Wrinkles or creases

• The transfer roller may be dirty. See “Cleaning the Inside”

page 6.4

• Check if the toner is leaking. Clean inside the printer.

Back of printouts dirty

• The toner cartridge may not be installed properly. Remove

the cartridge and reinsert it.

• The toner cartridge may be defective and need replacing.

Install a new toner cartridge.

• The printer may require repairs. Contact a service

representative.

AaBbCc
AaBbCc
AaBbCc

AaBbCc

AaBbCc
AaBbCc
AaBbCc

AaBbCc
AaBbCc

AaBbCc
AaBbCc
AaBbCc

AaBbCc

AaBbCc
AaBbCc
AaBbCc

AaBbCc
AaBbCc

AaBbCc
AaBbCc
AaBbCc

AaBbCc

AaBbCc
AaBbCc
AaBbCc

AaBbCc
AaBbCc

AaBbCc
AaBbCc
AaBbCc

AaBbCc

AaBbCc
AaBbCc
AaBbCc

AaBbCc
AaBbCc

Black pages

Solving Print Quality Problems

Summary of Contents for Phaser 3310









































































































































































































Search results

Summary of Contents for Phaser 3310

Reviews:

Related manuals for Phaser 3310

Brands by name

Popular brands

Xerox Phaser 3310, User Manual

Search results

Summary of Contents for Phaser 3310

Reviews:

Related manuals for Phaser 3310

Brands by name

Popular brands