Westermo GD-01 TCP Interface Manual Download Page 99

Page: 99 / 206

6196-2220

+DOPT – Others radio link parameters

Description:

This command allows some supplementary radio link protocol parameters to be
changed.

Syntax:

AT+DOPT=<reset_allowed>,<dtx_allowed>

Command example

Possible responses

Note

AT+DOPT=1

Set new parameters

AT+DOPT=? (0,1),(0,1)

Test

command, result:

DTX is supported

AT+DOPT=1,1

Set new parameters

AT+DOPT? 1,1

Current

values

Defined values:

<reset_allowed>

Data communication is hung up in case of bad radio link.

(default) Data communication continues in case of bad radio link (possi-
ble loss of data)

< dtx_allowed >

Normal mode

(default) Economic battery mode
(not supported by all networks).

Summary of Contents for GD-01 TCP















































































































































































































Search results

Summary of Contents for GD-01 TCP

Reviews:

Related manuals for GD-01 TCP

Brands by name

Popular brands

Westermo GD-01 TCP, Interface Manual

Search results

Summary of Contents for GD-01 TCP

Reviews:

Related manuals for GD-01 TCP

Brands by name

Popular brands