Westermo GD-01 TCP Interface Manual Download Page 32 | Manualshive

Page: 32 / 206

background image

32

6196-2220

+CPOL – Preferred operator list

Description:

This command is used to edit the SIM preferred list of networks.

Syntax:

AT+CPOL= [ <index> ][ , <format> [ , <oper> ] ]

The different possibilities are:

• AT+CPOL = <index> to delete an entry.
• AT+CPOL = , <format> to set the format used by the read command (AT+CPOL?).
• AT+CPOL = , <format>, <oper> to put <oper> in the next free location.
• AT+CPOL = <index> , <format> , <oper> to write <oper> in the <format> at the

<index>.

The supported format are the same as for the +COPS command.
The length of this list is limited to 8 entries.

«
...
30
31
32
33
34
...
»

Summary of Contents for GD-01 TCP















































































































































































































Reviews:

No comments

Related manuals for GD-01 TCP

Brand: Campbell Pages: 14

Brand: Sierra Wireless Pages: 12

Brand: EpiCom Pages: 25

Brand: Data-Linc Group Pages: 27

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Active Crystals FM02SW31

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Active Crystals FM02SW30

Brand: Philips Pages: 2

RESPIRONICS DreamStation

Brand: Philips Pages: 28

Brand: Philips Pages: 104

Active Crystals FM02SW30

Brand: Philips Pages: 104

Brand: GDI Pages: 7

Brand: GDI Pages: 16

Brand: Paradyne Pages: 24

Brand: Spectrum Technologies Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands