Westermo GD-01 TCP Interface Manual Download Page 142

Page: 142 / 206

142

6196-2220

+CPHS – CPHS command

Description:

This command is used to activate, deactivate or interrogate a CPHS feature (e.g.Voice
Mail Indicator, Mail Box Number...)

NOTE:

This command may CME ERROR: 3 if the CPHS feature is disabled

or if the SIM card does not support this CPHS feature.

Syntax

AT+CPHS=<Mode>,<FctId>

Command example

Possible responses

Note

AT+CPHS=<Mode>,<FctId> OK

+CME ERROR: 3
+CPHS: <FctId1>,<Status>

<CR<LF>

+CPHS: <FctId2>,<Status>

<CR<LF>

AT+CPHS? ...

+CPHS: <FctIdn>,<Status>

<CR<LF>

AT+CPHS=? OK

Defined values:

<Mode>

Deactivate a CPHS feature

Activate a CPHS feature

Interrogate a CPHS status

<FctId>

Voice Mail Indicator

Mail Box Number

<Status>

CPHS feature disabled

CPHS feature enabled

Summary of Contents for GD-01 TCP















































































































































































































Search results

Summary of Contents for GD-01 TCP

Reviews:

Related manuals for GD-01 TCP

Brands by name

Popular brands

Westermo GD-01 TCP, Interface Manual

Search results

Summary of Contents for GD-01 TCP

Reviews:

Related manuals for GD-01 TCP

Brands by name

Popular brands