Westermo GD-01 TCP Interface Manual Download Page 80

Page: 80 / 206

6196-2220

+CLIR – Calling line identification restriction

Description:

This command allows control of the calling line identification restriction supplementary
service.

Syntax:

AT+CLIR=<n>

Response Syntax:

+CLIR :<n>,<m> (for AT+CLIR ?)

Command example

Possible responses

Note

AT+CLIR=2 OK

AT+CLIR ?

+CLIR :<n>,<m>

Ask for current

functionality, result: <n>
and <m> as defined here-
below

Defined values:

<n>

Sets the line ID restriction for outgoing calls

Presentation indicator is used according to the subscription of the CLIR service

CLIR invocation

CLIR suppression

<m>

Shows the subscriber CLIR status in the network

CLIR not provisioned

CLIR provisioned in permanent mode

Unknown (no network...)

CLIR temporary mode presentation restricted

CLIR temporary mode presentation allowed.80

Summary of Contents for GD-01 TCP















































































































































































































Search results

Summary of Contents for GD-01 TCP

Reviews:

Related manuals for GD-01 TCP

Brands by name

Popular brands

Westermo GD-01 TCP, Interface Manual

Search results

Summary of Contents for GD-01 TCP

Reviews:

Related manuals for GD-01 TCP

Brands by name

Popular brands