Westermo GD-01 TCP Interface Manual Download Page 175

Page: 175 / 206

175

6196-2220

AT+WGIPCPINF – Get IPCP informations, (GPRS command)

Description

This command get the current IPCP informations to use with a particular cid after a PDP
activation.

These parameters are not saved in persistent memory and are only available during the
life of the PDP context.

If the cid is not defined then ERROR is returned.

Syntax

AT+WGIPCPINF=[<cid> [,<cid [,...]]]

AT+WGIPCPINF=?

Response Syntax:

+WGIPCPINF: <cid>,<@DNS1>,<@DNS2>,<@gateway>

[<CR><LF> +WGIPCPINF: <cid>,<@DNS1>,<@DNS2>,<@gateway>[...]]

ERROR

Response on ” AT+WGIPCPINF=?”:

+WGIPCPINF: (list of supported <cid>s)

Defined Values:

<cid>

(PDP Context Identifier) a numeric parameter (1-32) which specifies a particular PDP
context definition.The parameter is local to the TE-MT interface and is used in other
PDP context-related commands.

<@DNS1> and <@DNS2>:

String parameters which are IPV4 DNS address.

<@gateway>:

String parameter which is IPV4 address

NOTE:

These parameters are optional and depend of the operator setup.

Command example

Possible responses

AT+WGIPCPINF

+WGIPCPINF:1,62.201.129.99,62.201.159.99,13.9..130
+WGIPCPINF:2
+WGIPCPINF:3
OK

Summary of Contents for GD-01 TCP















































































































































































































Search results

Summary of Contents for GD-01 TCP

Reviews:

Related manuals for GD-01 TCP

Brands by name

Popular brands

Westermo GD-01 TCP, Interface Manual

Search results

Summary of Contents for GD-01 TCP

Reviews:

Related manuals for GD-01 TCP

Brands by name

Popular brands