Westermo GD-01 TCP Interface Manual Download Page 132

Page: 132 / 206

132

6196-2220

+WDWL – Downloading

Description:

This command switches the product to download mode. Downloading is performed
using the 1K-XMODEM protocol.

Syntax:

AT+WDWL

Command example

Possible responses

Note

AT+WDWL

+WDWL: 0

Switch on downloading
mode, start the down-
loading

...Downloading in
progress

AT+CFUN=1

Reset the product
at the end

+WDR – Data Rate

Description:

This command allows the data rate for bearer data to be configured
(available for outgoing calls only).

Syntax:

AT+WDR=<n>

Command example

Possible responses

Note

AT+WDR=<n>

AT+WDR=?

+WDR: (0-2)

Possible values, Half Rate
available.

AT+WDR?

+WDR: <n>

Request current value

AT+WDR=1

Configure voice type
FR,HR with HR prefered.
Bearer is configured

AT+WDR=3 +CME

ERROR: 3

Syntax

error

AT+WDR?

+WDR: 1

Ask the current value

Defined values:

<n>

Data coding type.

FR, HR with HR preferred

HR, FR with FR preferred.

Summary of Contents for GD-01 TCP















































































































































































































Search results

Summary of Contents for GD-01 TCP

Reviews:

Related manuals for GD-01 TCP

Brands by name

Popular brands

Westermo GD-01 TCP, Interface Manual

Search results

Summary of Contents for GD-01 TCP

Reviews:

Related manuals for GD-01 TCP

Brands by name

Popular brands